Skip to content

8 Best PEX Crimp and Cinch Tools for Plumbers, Compared by Ring Type, Sizes and Calibration

Updated November 16, 2026Written and fact-checked by Daniel Wilson19 min readHow we checked this

Some links on this page are affiliate links. If you buy through one, we may earn a commission at no extra cost to you. See our affiliate disclosure.

Plumber using a hand crimp tool on a copper ring and PEX tubing at a manifold

Quick answer: For most plumbers, match the tool to the ring you buy: copper crimp rings (ASTM F1807) need a crimp tool, while stainless cinch clamps (ASTM F2098) need a cinch tool. A budget ratcheting cinch tool covers most service work, the iCrimp F1807 kit is a full-size copper crimp set, and Milwaukee’s M18 press kit is the pro pick for all-day crews.

Two things decide a good joint: the right tool for the ring, and a checked crimp. Below: specs, who should skip each tool, and what the sources disagree on.

The 8 Best PEX Crimp and Cinch Tools at a Glance

Eight tools from iCrimp, Apollo, SharkBite and Milwaukee. Tap a photo or a button to see the current price and listing details.

The 8 PEX crimp and cinch tools at a glance
ProductBest forPrice categoryNamed byBuy
iCrimp KG1096 Ratcheting PEX Cinch Tool for 3/8 to 1 Inch Stainless ClampsiCrimp KG1096 Ratcheting PEX Cinch Tool for 3/8 to 1 Inch Stainless ClampsThe cheapest way into stainless cinch clampsBudgetiCrimp and IWISS guidanceCheck price
iCrimp PEX Cinch Tool Kit with Clamps and Cutter (Crimp-Cut-Clamp Set)iCrimp PEX Cinch Tool Kit with Clamps and Cutter (Crimp-Cut-Clamp Set)A cinch tool, cutter and starter clamps in one low-cost kitBudgetBob Vila reviewSee details
iCrimp ICP-BJ02 One-Handed PEX Cinch Clamp TooliCrimp ICP-BJ02 One-Handed PEX Cinch Clamp ToolA one-handed cinch tool for tight joist baysBudgetiCrimp listingCompare options
iCrimp F1807 Copper Ring Crimping Tool Kit for 3/8, 1/2, 3/4 and 1 Inch PEXiCrimp F1807 Copper Ring Crimping Tool Kit for 3/8, 1/2, 3/4 and 1 Inch PEXA full-size crimp kit with all four jaw sizesMid-rangeBob Vila reviewShop now
iCrimp IWS-1807CN Angle Head PEX Crimping Tool Kit, 1/2 and 3/4 InchiCrimp IWS-1807CN Angle Head PEX Crimping Tool Kit, 1/2 and 3/4 InchAngle-head reach for copper rings in cramped spacesMid-rangeBob Vila reviewSee current price
Apollo PEX 69PTKH0015K Multi-Head Crimp Tool Kit, 3/8 to 1 InchApollo PEX 69PTKH0015K Multi-Head Crimp Tool Kit, 3/8 to 1 InchA long-leverage multi-head kit from a PEX valve makerMid-rangeApollo and Bob Vila dataCheck availability
SharkBite 23251Z PEX Crimp Tool, 1/2 and 3/4 Inch Dual HeadSharkBite 23251Z PEX Crimp Tool, 1/2 and 3/4 Inch Dual HeadA factory-calibrated two-size tool for service workMid-rangeDistributor specification pagesView listing
Milwaukee 2674-22C M18 Short Throw Press Tool Kit with PEX Crimp JawsMilwaukee 2674-22C M18 Short Throw Press Tool Kit with PEX Crimp JawsA cordless press tool that needs no calibrationPremiumMilwaukee kit dataCheck sizes

Price categories reflect the listing price when we checked: Budget is under $50, Mid-range is $50 to $150 and Premium is above $150. Prices change often.

Infographic with six steps for making a reliable PEX crimp or cinch connection
How to make a reliable PEX connection in six steps

Which PEX Tool for Which Job (and Who Should Skip Each)

Which PEX tool for which job
If you needLook atWhat the sources say
Stainless cinch clamps on a budgetiCrimp KG1096, iCrimp kitASTM F2098 clamps; ratcheting tool covers 3/8 to 1 inch.
A starter kit with cutter and clampsiCrimp Crimp-Cut-Clamp kitBob Vila: 30 clamps and a cutter.
One hand in a tight spaceiCrimp ICP-BJ02One-handed cinch operation.
Copper rings in all four sizesiCrimp F1807 kit, Apollo multi-head3/8, 1/2, 3/4 and 1 inch jaws.
Copper rings in cramped spacesiCrimp IWS-1807CNOffset head, 13.7 inches.
A simple two-size crimperSharkBite 23251Z1/2 and 3/4 inch, factory calibrated.
All-day, no-calibration crimpingMilwaukee 2674-22CAuto cycle, about 3 seconds, no calibration interval.

Who should skip each tool

Skip it if
ProductSkip it ifBecause
iCrimp KG1096You use copper crimp ringsCinch tool only
iCrimp kitYou want a calibratable toolCannot be calibrated
iCrimp ICP-BJ02You use copper crimp ringsCinch tool only
iCrimp F1807 kitYou work in tight spacesLong handles
iCrimp IWS-1807CNYou crimp 1 inch ringsOnly 1/2 and 3/4 inch
Apollo multi-headYou work in tight spacesLong, no cutter
SharkBite 23251ZYou need 1 inch or 3/8 inchTwo sizes only
Milwaukee 2674-22CYou crimp a few joints a monthPremium price

Best PEX Cinch Clamp Tools

Stainless clamp tools: one tool for every size.

iCrimp KG1096 Ratcheting PEX Cinch Tool for 3/8 to 1 Inch Stainless Clamps

Best for: the cheapest way into stainless cinch clamps

iCrimp KG1096 ratcheting PEX cinch tool with red handles and a stainless clamp

iCrimp KG1096 Ratcheting PEX Cinch Tool for 3/8 to 1 Inch Stainless Clamps

Price category: Budget

A ratcheting hand tool for 3/8 to 1 inch stainless cinch clamps, listed with a calibration gauge.

Check price

The KG1096 is a ratcheting cinch tool for stainless steel cinch clamps. The listing gives a 3/8 to 1 inch clamp range and says a calibration gauge is included. IWISS describes its cinch tool as working from 3/8 to 1 inch and suited to odd jobs, and says it needs no calibration out of the box.

Cinch clamps fall under ASTM F2098, while copper crimp rings follow F1807 for metal insert fittings and F2159 for plastic (Canarsee). A cinch tool will not close copper crimp rings, so buy the tool that matches the rings you stock.

Spec sheet:

  • Ring type: stainless steel cinch clamps, 3/8 to 1 inch (listing).
  • Action: ratcheting, one tool for all clamp sizes (IWISS).
  • Calibration: listing says a gauge is included; IWISS says none is needed out of the box (IWISS).

What this means for you (general advice): A low-cost tool for occasional PEX work, repairs and service calls.

Fit and sizing: Plier-style body with red handles and a ratchet.

Versions to check: iCrimp sells several cinch tools. Look for KG1096 in the model line.

Watch for: Needs hand strength on 1 inch clamps; sold as a tool, not a full kit.

Skip it if: you work with copper crimp rings.

iCrimp PEX Cinch Tool Kit with Clamps and Cutter (Crimp-Cut-Clamp Set)

Best for: A cinch tool, cutter and starter clamps in one low-cost kit

iCrimp PEX crimping tool kit with cinch tool, tubing cutter and stainless clamps in a blister pack

iCrimp PEX Cinch Tool Kit with Clamps and Cutter (Crimp-Cut-Clamp Set)

Price category: Budget

An 11 inch cinch tool for 3/8 to 1 inch clamps, with 30 clamps and a tubing cutter.

See details

Bob Vila names this iCrimp kit its best bang for the buck: an 11.02 inch cinch tool that works with 3/8, 1/2, 3/4 and 1 inch PEX, with 30 clamps and a cutter. It calls it well calibrated out of the box.

Bob Vila’s downsides: it needs more hand strength than a competing clamp tool, the removal feature did not work well for its reviewers, and the tool cannot be calibrated. If your tool ever drifts, a ratcheting tool with a gauge may be easier to live with.

Spec sheet:

  • Length: 11.02 inches; sizes 3/8, 1/2, 3/4 and 1 inch (Bob Vila).
  • Includes: 30 clamps and a tubing cutter (Bob Vila).
  • Calibration: cannot be calibrated, per Bob Vila.

What this means for you (general advice): A starter kit that covers cutting and clamping for a first job.

Fit and sizing: Blister pack with the cinch tool, a cutter and clamps.

Versions to check: iCrimp sells several kits with similar photos. Look for Crimp-Cut-Clamp Set in the model line.

Watch for: Takes hand strength; cannot be calibrated.

Skip it if: you work with copper crimp rings.

iCrimp ICP-BJ02 One-Handed PEX Cinch Clamp Tool

Best for: A one-handed cinch tool for tight joist bays

iCrimp ICP-BJ02 one-handed PEX cinch tool with orange and blue handles

iCrimp ICP-BJ02 One-Handed PEX Cinch Clamp Tool

Price category: Budget

A patented one-handed cinch tool for 3/8 to 1 inch stainless clamps.

Compare options

iCrimp’s listing describes the ICP-BJ02 as a patented one-handed cinch tool for 3/8, 1/2, 3/4 and 1 inch stainless clamps. A one-handed design matters when you are reaching around a joist or into a wall cavity with the other hand on the pipe.

Tight spaces are the main reason many plumbers choose cinch clamps: forum threads on crimp rings often say the long throw of crimp-tool handles makes them hard to use in tight spaces. The short travel of a cinch tool is the usual answer.

Spec sheet:

  • Ring type: stainless steel cinch clamps, 3/8 to 1 inch (listing).
  • Action: one-handed operation (listing).

What this means for you (general advice): A good second tool for cramped spots and manifold work.

Fit and sizing: Compact one-hand body with large handles.

Versions to check: iCrimp sells several one-hand cinch tools. Look for ICP-BJ02 in the model line.

Watch for: Little independent data beyond the listing.

Skip it if: you use copper crimp rings.

Best PEX Copper Ring Crimp Tools

Manual crimpers for copper rings, from compact to full kits.

iCrimp F1807 Copper Ring Crimping Tool Kit for 3/8, 1/2, 3/4 and 1 Inch PEX

Best for: A full-size crimp kit with all four jaw sizes

iCrimp F1807 copper ring PEX crimping tool kit in a blue case with changeable jaws and gauge

iCrimp F1807 Copper Ring Crimping Tool Kit for 3/8, 1/2, 3/4 and 1 Inch PEX

Price category: Mid-range

A 15.55 inch crimp tool kit for 3/8 to 1 inch copper rings, with a cutter, gauge and calibration wrench.

Shop now

Bob Vila names it best overall: a 15.55 inch crimp tool kit for 3/8, 1/2, 3/4 and 1 inch rings with easy-change jaws, a PEX cutter, a crimp-removal tool, a go/no-go gauge, a calibration wrench and a hard case. Its listed downside is that snugging the rings takes some hand strength.

IWISS says the kit uses a 1 inch jaw plus three changeable jaws for 3/8 to 3/4 inch, and that it suits less cramped work than the compact tools. It is the kit to buy if you want one crimper for every residential size.

Spec sheet:

  • Length: 15.55 inches; sizes 3/8, 1/2, 3/4 and 1 inch (Bob Vila).
  • Includes: cutter, ring removal tool, go/no-go gauge, calibration wrench, case (Bob Vila).
  • Standard: meets ASTM F1807 per IWISS.

What this means for you (general advice): A full set for a plumber who wants copper rings, a gauge and a way to recalibrate.

Fit and sizing: Blue hard case with the tool, jaws, cutter and gauge.

Versions to check: iCrimp sells several F1807 kits. Look for IWS-FA-1807-KIT in the model line.

Watch for: Long handles are awkward in tight spaces; takes hand strength.

Skip it if: you work in cramped spaces most of the time.

iCrimp IWS-1807CN Angle Head PEX Crimping Tool Kit, 1/2 and 3/4 Inch

Best for: angle-head reach for copper rings in cramped spaces

iCrimp IWS-1807CN angle head PEX crimping tool kit in an orange case

iCrimp IWS-1807CN Angle Head PEX Crimping Tool Kit, 1/2 and 3/4 Inch

Price category: Mid-range

A 13.7 inch angle head crimp kit for 1/2 and 3/4 inch copper rings, with a cutter and gauge.

See current price

Bob Vila lists the iCrimp angle-head F1807 kit as best for tight spaces: an offset head that reaches hard-to-access crimps, 13.7 inches long, for 1/2 and 3/4 inch rings, with built-in jaws, a cutter, rings, a gauge and a case.

Bob Vila notes its reviewers did not review this model, so treat the claims as the maker’s. Many service plumbers only need 1/2 and 3/4 inch, which makes the angle head a sensible pick for crawlspaces and ceilings.

Spec sheet:

  • Length: 13.7 inches; sizes 1/2 and 3/4 inch (Bob Vila).
  • Includes: cutter, rings, gauge, case (Bob Vila).
  • Head: offset (angle) design (Bob Vila).

What this means for you (general advice): A copper-ring crimper that fits where a straight tool will not.

Fit and sizing: Angled head with an orange hard case.

Versions to check: iCrimp sells several kits. Look for IWS-1807CN in the model line.

Watch for: Only 1/2 and 3/4 inch; no 1 inch jaw.

Skip it if: you crimp 1 inch rings regularly.

Apollo PEX 69PTKH0015K Multi-Head Crimp Tool Kit, 3/8 to 1 Inch

Best for: A long-leverage multi-head kit from a PEX valve maker

Apollo 69PTKH0015K multi-head PEX crimp tool kit with yellow handles and interchangeable jaws

Apollo PEX 69PTKH0015K Multi-Head Crimp Tool Kit, 3/8 to 1 Inch

Price category: Mid-range

A multi-head crimp tool for 3/8 to 1 inch copper rings, with a go/no-go gauge and wrench.

Check availability

Distributor listings give the 69PTKH0015K four interchangeable jaws for 3/8 to 1 inch, a go/no-go gauge, an adjusting wrench, a case, comfort-grip handles and ASTM F1807 compliance (DK Hardware). Bob Vila adds strong leverage rated up to 100 pounds of force.

The same Bob Vila entry criticizes the kit for lacking a PEX cutter. Sources disagree on handle length: Bob Vila lists 17 inches, while a retailer lists 15 inches (DK Hardware). Plan for a long tool either way.

Spec sheet:

What this means for you (general advice): A tough, simple kit for crews that already buy Apollo fittings.

Fit and sizing: Black body with yellow handles and swappable heads.

Versions to check: Apollo sells several crimp tools. Look for 69PTKH0015K in the model line.

Watch for: No cutter; sources disagree on handle length.

Skip it if: you work in tight spaces.

SharkBite 23251Z PEX Crimp Tool, 1/2 and 3/4 Inch Dual Head

Best for: A factory-calibrated two-size tool for service work

SharkBite 23251Z dual head PEX crimp tool with blue handles

SharkBite 23251Z PEX Crimp Tool, 1/2 and 3/4 Inch Dual Head

Price category: Mid-range

A dual-head crimp tool for 1/2 and 3/4 inch copper rings, factory calibrated, with a go/no-go gauge.

View listing

Distributor pages describe the SharkBite 23251 family as a dual-head 1/2 and 3/4 inch crimp tool that is factory calibrated, meets ASTM F1807 and ships with a go/no-go gauge (Ferguson). Pace lists it at about 15 inches long with a steel body (Pace Supply).

Bob Vila’s SharkBite pick is a different, multi-size model that weighs just under 4 pounds and whose handles open nearly 180 degrees, which does not work in restricted spots (Bob Vila). The 23251Z is the simpler two-size tool, with no jaws to swap or lose.

Spec sheet:

  • Sizes: 1/2 and 3/4 inch dual head (Ferguson).
  • Standard: ASTM F1807, factory calibrated, go/no-go gauge included (Ferguson).
  • Length: about 15 inches, steel body (Pace Supply).

What this means for you (general advice): A no-fuss crimper for plumbers who only use 1/2 and 3/4 inch ring.

Fit and sizing: Black steel body with blue grips and two fixed heads.

Versions to check: SharkBite sells several PEX tools. Look for 23251Z in the model line.

Watch for: Only two sizes; long handles in tight spaces.

Skip it if: you need 1 inch or 3/8 inch rings.

Best Cordless PEX Press Tool

A battery tool for crews that crimp all day.

Milwaukee 2674-22C M18 Short Throw Press Tool Kit with PEX Crimp Jaws

Best for: A cordless press tool that needs no calibration

Milwaukee 2674-22C M18 short throw press tool kit with PEX crimp jaws, batteries and case

Milwaukee 2674-22C M18 Short Throw Press Tool Kit with PEX Crimp Jaws

Price category: Premium

A one-handed M18 press tool kit with 1/2, 3/4 and 1 inch PEX crimp jaws, two batteries and a charger.

Check sizes

Distributor listings give the 2674-22C a one-handed short-throw press with 1/2, 3/4 and 1 inch PEX crimp jaws, two M18 CP2.0 batteries, a charger and a case. It crimps F1807 and F2159 rings up to 1 inch, has an auto-cycle that completes each press, a green LED, no calibration interval and a cycle of roughly 3 seconds (F.W. Webb).

It is about 13.5 inches long and 4.8 pounds in distributor listings. Bob Vila calls a related Milwaukee press kit its best professional pick, with 3/8 and 5/8 inch jaws costing extra, and Milwaukee’s marketing says the tool is optimized for residential installs (Bob Vila).

Spec sheet:

  • Jaws: 1/2, 3/4 and 1 inch PEX crimp (F.W. Webb).
  • Crimps: F1807 and F2159 rings up to 1 inch; no calibration interval (F.W. Webb).
  • Warranty: 5 years on the tool; 2 years on batteries per this listing (F.W. Webb).

What this means for you (general advice): For crews that crimp all day and want repeatable joints without hand fatigue.

Fit and sizing: Red M18 tool with a hard case and jaw set.

Versions to check: Milwaukee sells several press kits and bare tools. Look for 2674-22C in the title.

Watch for: Most expensive in this list; 3/8 inch jaw not in the kit.

Skip it if: you only crimp a few joints a month.

Also Worth Knowing: Picks Without a Buy Button

These came up in research, but we could not match them to a clear listing from a US seller, or they sit outside the hand-tool list.

  • iCrimp IWS-FAS compact copper ring kit: Bob Vila lists it as best compact, a 12.2 inch crimper for 3/8 to 1 inch rings with a gauge and hard case. We did not find a clean listing that matched the model.
  • Plumbflex clamp tool kit: Bob Vila names it runner-up for 1/2 and 3/4 inch clamps with a shorter handle for tight spots and no gauge. We did not find a matching listing from a US seller.
  • Expansion tools for PEX-A: these use a different connection system and are outside this list.
  • Zurn QickClamp tools: Sioux Chief’s instruction sheet for its cinch tool says not to use it with Zurn QickClamp rings (Sioux Chief). Check the ring maker’s tool list.

PEX Crimp and Cinch Tools Specs Compared

Figures come from the maker or source named in each section; some sources disagree.

Specs compared
ToolRing typeSizesLengthCalibrationIncludes
iCrimp KG1096Stainless cinch3/8 to 1 inNot statedGauge per listingTool only
iCrimp kitStainless cinch3/8 to 1 in11.02 inCannot be calibrated30 clamps, cutter
iCrimp ICP-BJ02Stainless cinch3/8 to 1 inNot statedNot statedTool
iCrimp F1807 kitCopper crimp3/8 to 1 in15.55 inWrench includedCutter, gauge, case
iCrimp IWS-1807CNCopper crimp1/2 and 3/4 in13.7 inNot statedCutter, gauge, case
Apollo multi-headCopper crimp3/8 to 1 in15 to 17 inWrench includedGauge, case
SharkBite 23251ZCopper crimp1/2 and 3/4 inAbout 15 inFactory calibratedGauge
Milwaukee 2674-22CCopper crimp (press)1/2, 3/4, 1 in13.5 inNone requiredBatteries, charger, case

Not stated means the source we used did not publish it. Lengths come from Bob Vila or distributor sheets and vary.

Our PEX Tool Evaluation Framework

We score each tool on five questions using only what the named sources published.

  1. Ring match. Cinch clamps and copper rings need different tools.
  2. Size range. Which PEX sizes the tool covers.
  3. Calibration. How you know the crimp is right.
  4. Reach. Handle length and head shape for tight spaces.
  5. Recurring drawback. The limit sources raise most often.
How each product scores
ToolRingSizesCalibrationReachMain drawback
Milwaukee 2674-22CCopper1/2 to 1None required13.5 in, one handPremium price
iCrimp F1807 kitCopper3/8 to 1Wrench included15.55 inHand strength
Apollo multi-headCopper3/8 to 1Wrench included15 to 17 inNo cutter
SharkBite 23251ZCopper1/2, 3/4FactoryAbout 15 inTwo sizes
iCrimp IWS-1807CNCopper1/2, 3/4Not statedAngle headTwo sizes
iCrimp ICP-BJ02Cinch3/8 to 1Not statedOne handLittle data
iCrimp kitCinch3/8 to 1Cannot be calibrated11.02 inHand strength
iCrimp KG1096Cinch3/8 to 1Gauge per listingPlier styleHand strength

Ratings are from manufacturer, distributor or Bob Vila sheets; none were measured by us.

How to Choose a PEX Crimp or Cinch Tool

  • Match the tool to the ring. Cinch clamps follow ASTM F2098 and copper crimp rings follow F1807 or F2159 (Canarsee). A cinch tool will not close copper rings.
  • Pick the sizes you use. Many residential jobs only need 1/2 and 3/4 inch; a four-size kit adds 3/8 and 1 inch.
  • Weigh the trade-offs of each ring. Bob Vila says copper is burlier but more prone to corrosion, while stainless clamps are easier to install and less likely to corrode but thinner and may bend more easily.
  • Plan for tight spaces. Long crimp-tool handles need room to open; cinch tools and angle-head crimpers fit better (Bob Vila).
  • Check calibration. Boshart says to make a test crimp at the start of a job, since normal wear gradually enlarges the crimp diameter.
  • Use the gauge on every joint. Boshart says the ring must fit the GO slot and not the NO-GO slot, with the gauge held at 90 degrees.

More reading: our plumber tools hub, best pipe wrenches and all field service gear.

Where the Sources Disagree

Crimp versus cinch. Bob Vila says copper is tougher but corrosion-prone and stainless is easier to install but thinner. Trade forum threads often favor cinch clamps for speed and tight spaces. General advice: use whichever ring system your fittings and local code allow, and keep the matching tool.

Calibration. Bob Vila says the iCrimp cinch kit cannot be calibrated, IWISS says its cinch tool needs no calibration out of the box, and the KG1096 listing says a gauge is included. Check your own joints with a gauge or a test crimp.

Apollo handle length. Bob Vila lists 17 inches for the multi-head kit and a retailer lists 15 inches.

Milwaukee kit contents. Bob Vila’s Milwaukee entry lists 3/8 and 5/8 inch jaws as extras; the 2674-22C kit listed here ships with 1/2, 3/4 and 1 inch jaws.

Warranty terms. Distributor pages describe the Milwaukee warranty differently, from a 5 year tool warranty with a 2 year battery warranty to a 2 year jaw warranty. Check Milwaukee’s page at purchase.

Questions About PEX Crimp and Cinch Tools, Answered

“Can I use a cinch tool on copper crimp rings?”

No. Cinch clamps are stainless bands with tabs (ASTM F2098); copper rings follow F1807 or F2159. Use the tool made for the ring.

“How do I know my crimp is good?”

Use a go/no-go gauge at 90 degrees: the ring must fit the GO slot and rotate freely and not fit the NO-GO slot, per Boshart. If it fails, disassemble and redo the joint.

“How far from the pipe end should the ring sit?”

Boshart says to slide the ring so it sits about 1/8 to 1/4 inch from the pipe end, directly over the fitting’s barbs.

“Do I need to calibrate my tool?”

Normal wear gradually enlarges the crimp diameter, per Boshart, so make a test crimp at the start of a job and adjust or replace the tool if it fails the gauge.

“What do plumbers use in tight spaces?”

Cinch tools, angle-head crimpers and one-handed tools. Bob Vila says one SharkBite handle opens nearly 180 degrees and does not work in restricted spots.

“Should I cut PEX with a hacksaw?”

No. Boshart says to cut square and smooth with a pipe cutter and not to use a hacksaw.

“Is a cordless press tool worth it?”

For crews crimping all day, yes: Milwaukee lists no calibration interval, an auto cycle of about 3 seconds and a green LED. For occasional work, a manual tool is cheaper.

“Which tool works with PEX-A?”

PEX-A is often joined with expansion tools; crimp and cinch tools are commonly used on PEX-A and PEX-B with the right rings, per Canarsee. Check the fitting maker’s instructions.

Mistakes to Avoid With PEX Tools

  • Using the wrong tool for the ring. Match cinch tools to clamps and crimp tools to copper rings.
  • Skipping the gauge. Check every joint at 90 degrees.
  • Misplacing the ring. Keep it 1/8 to 1/4 inch from the pipe end, per Boshart.
  • Using a hacksaw. Cut square with a pipe cutter.
  • Ignoring wear. Make a test crimp at the start of each job.
  • Crimping at an angle. Hold the tool at 90 degrees to the fitting.

How we checked this

  • Field Services HQ compared maker and distributor pages from iCrimp, Apollo, SharkBite and Milwaukee with Bob Vila and Boshart guidance, plus common questions from trade forum threads.
  • Each figure names the source that published it, and where sources disagree we say so. Our own readings are labeled general advice.
  • Buy buttons go to US listings matched to each model, with stock and seller checked; as an Amazon Associate we earn from qualifying purchases. Price categories: Budget under $50, Mid-range $50 to $150, Premium above $150.

PEX Crimp and Cinch Tool FAQ

What is the best PEX crimp tool overall?

For copper rings, the iCrimp F1807 kit or the SharkBite 23251Z; for all-day crews, the Milwaukee M18 press kit.

What is the best budget PEX tool?

The iCrimp KG1096 ratcheting cinch tool.

Crimp or cinch?

Match the tool to the ring your fittings use; cinch tools are easier in tight spaces.

Which standard covers copper crimp rings?

ASTM F1807 for metal insert fittings and F2159 for plastic insert fittings.

How do I check a crimp?

Use a go/no-go gauge at 90 degrees.

How far from the end does the ring go?

About 1/8 to 1/4 inch.

Do I need a PEX cutter?

Yes, for square, smooth cuts; do not use a hacksaw.

Is a cordless press tool worth it?

For all-day crimping, yes; for occasional work, no.

The Short Version

Best budget cinch tool: iCrimp KG1096. Starter kit: iCrimp Crimp-Cut-Clamp. Tight spaces: iCrimp ICP-BJ02 or IWS-1807CN. Four-size copper kit: iCrimp F1807 or Apollo. Simple two-size crimper: SharkBite 23251Z. All-day crews: Milwaukee 2674-22C.

Sources

Author

  • Daniel Wilson

    I’m Daniel Wilson, a field service operations and technology expert with over 14 years of experience in field service management, maintenance, business software, and digital transformation.

    My background covers end-to-end service operations, including work orders, scheduling, dispatching, route planning, technician management, preventive and predictive maintenance, asset tracking, inventory, CRM, service contracts, invoicing, reporting, and mobile field management. I also track emerging trends in FSM software, ERP systems, CRM platforms, AI, and automation.

    At Field Services HQ, I share practical insights on operational efficiency, technician productivity, software adoption, and field service strategy. I believe effective operations combine people, processes, and technology to simplify work rather than add complexity.

    My objective is to deliver actionable, reliable advice that empowers field service businesses to make smart technology choices, streamline operations, and enhance customer service.

Scroll to Top